Painting Exterior Windows

When it comes to painting the outside of your windows, look for a quality exterior trim paint. Trim paint is specially formulated to be tough and long-lasting. When you’re painting, don’t worry about getting some paint on the glass. Just wait until it’s dry, then use a single-edge razor blade to scrape off the excess.

 

 

When painting double-hung windows, start by removing the sash. Put the sash on a couple of sawhorses or a work table. If you can’t remove the sash, then work carefully so you don’t paint the window shut. Paint the sides of the vertical stiles first, using a 2-inch trim brush with just a small amount of paint.

 

 

Beginning in the upper left corner, paint downward until you reach the bottom of the sash. Lift up on the brush at the end of the stroke. Continue until the sides of all the vertical members are completed.

 

 

 

Paint both sides of any vertical and horizontal grills in the sash. If you get paint on the glass, let it dry, then scrape it off with a single-edge razor.

 

 

 

 

Now, paint both sides of the rails (horizontal sash members) on the upper sash.

 

 

 

 

Paint the faces of the grills, rails, and stiles on the upper sash. When completed, repeat the process for the lower sash.

 

 

 

 

When painting double-hung windows that are still in the jamb, pull the upper sash down and raise the lower sash so you can paint the surfaces that touch each other when the window is closed. Let the paint dry completely before closing the window.

 

 

 

Return the sashes to their normal position and paint the stops and jambs.

 

 

 

 

Paint the sides of the casing, then the faces of the casing, and continue to the sill. Use masking tape or a paint shield to keep trim paint off the siding. If you use tape, be sure to remove it as soon as the paint is dry to the touch.

Painting Exterior Walls

The Golden rule when working off ladders or scaffolding is safety first.
Make sure that you complete the painting of soffitts, fascias and guttering before you start the walls.
Paint walls in designated sections if you cane. an apex above a window, a section between two windows or between wall edge and window/door).
If the walls are of a fairly rough surface consider using roller to make the job easier.
If you are right-handed, then work from right to left in as far as you can do comfortably. This way you won’t be working across yourself, especially when working off a ladder.
Work from the top downwards; completing areas within natural breaks. e.g. between two windows or between a window and a down pipe.
It is wise to cover up bushes, flowerbeds and the lawn with dust-sheets.
Always use a pothook when you up a ladder; secure it firmly on the side of the ladder and attach your paint container. DO NOT hold the paint container in one hand and the paint brush in the other.
When using a roller on the walls, cut in one area at a time; roll and move on to the next area.
Use an extension pole on the roller so that you can reach as much as possible from the ground.

Painting – Exterior Door

Exterior doors are heavy and can be awkward to move – you’ll usually find it easier to paint them in place instead of trying to take them off their hinges. However, removing the doorknob and latch bolt makes the job a whole lot faster and neater.

With the door upright, you’ll have to be aware of catching drips and runs. Work one small, defined area at a time and try not to overload your paintbrush. Make sure all six sides are covered to protect your door from rotting, cracking and expanding.

First, apply paint to the inside of the top panels. Smooth out the paint, working with the grain, doing the recessed areas first, then the faces of the panels.

If the door has a vertical center stile, paint this next, and then blend in the brush marks from the center stile when you paint the horizontal rails.

Paint the rails (horizontal framing members), starting with the top rail and working your way to the bottom.

Paint the remaining vertical stiles, starting on the left. Feather the brush marks from the rails while they are still wet. Keep the line as straight as possible along the edge where the stiles meet the rails. Brush or roll the edges, but be careful not to get any runs on the face of the door.

There are now a wide variety of Deck finishes – Painting sundeck

Due to the growing popularity of decks, there are now a wide variety of Deck finishes – ranging from conventional penetrating ones to new water based latex ones. In the alkyd category, there are clears, semi transparent and opaque finishes. In latex, semi transparent and opaque.
Many homeowners are starting to use the semi transparent or opaque to maximize the protection and duration of their deck coating.
Begin by cleaning and power washing to remove dirt, mildew and old coatings. If you are using a clear, penetrating coatings, deck brightening products help restore a “new wood” look to the wood.. Both sides of the railings should also be power washed.

Brushes and Rollers – Once the deck is clean and thoroughly dry, start with a brush on the outside of the deck, on tops of the railing and work your way down to the deck, then in toward the house. Then switch to a roller for the deck, starting at an outside edge and working toward the house. Use even pressure on the roller on each board to give uniform coverage and sheen.
Spraying is another way to coat decks – faster than brush/roller, but you must be sure to protect scrubs etc. from overspray. Spray equipment can be rented at many paint stores, home centers or rental companies. Check with a paint professional for tip size and pressure setting – which will depend on the type of coating you use. Spray railings first, unless the railings are to be a different color than the deck. Then the deck should be coated first. One trip for protecting plants or other objects from overspray is to tape Kraft paper to the outside of the railing, which will catch the overspray. When spraying the deck itself, spray evenly over a six foot square area, then go over that area with a _ inch nap roller to spread coating evenly into deck. Continue this procedure in sections until deck is covered. Be sure to use a large shield (such as 4 ft square piece of cardboard) when painting alongside the house to protect it from overspray.

6 Exterior Decorating Tips To Revitalize Your Home

Spring has finally sprung, and it’s the perfect time to make a start on those DIY jobs that make a massive difference to how your home looks and feels – especially those exterior decorating projects!

We’re going to give you our top tips on sprucing up the exterior of your home so that you’re ready to welcome friends and family around for a BBQ or garden party.

Revitalise your house with these 6 exterior decorating projects

Paint Your Garden Fence:
A new colour will lift the whole exterior of your property, so rub that fence down with a wire brush and apply a couple of coats of wood treatment. Make sure that you use a soft brush to remove any loose dirt before applying the first coat. Easy to apply and offering many colour options, it’s ideal for the DIYer and provides 5 years of protection.

Paint Your Gate:
Is your metal gate looking sorry for itself? A rub down with some wire wool and sandpaper to remove any rust and dirt will prepare it perfectly for some metallic paint. Lay a sheet down to protect the floor, give it a good clean with sugar soap, and then apply primer. Once dry you can use a small brush to apply two coats of metal paint.

Paint Your Doorstep:
A coat or three of decent masonry paint can transform a worn doorstep and give your house a completely new look. As with all masonry painting, prep first with a good sand and clean before applying the paint.

Paint Your Window Sills And Surrounds:
Old Toronto terrace houses often have concrete window sills that look fantastic when painted. Rub them down with wire wool, fill in any holes with ready mixed stone repair and rendering, and then apply primer and paint. Use the same colour and technique for the arches and surrounds.

Jet Wash Your Paths:
A year’s worth of muck and grime will make any exterior paths or driveways look terrible, but a day with a hired jet wash and some elbow grease and your paths will soon look sparkling clean!

Paint Your House:
A fresh coat of paint to your house’s exterior will make it look like a new property. It’s best to stick to fairly simple and neutral colours in our climate rather than attempting to bring a little continental sparkle with a brighter colour – we simply don’t have the quality of light to pull that off successfully so white works best.

None of these jobs should be too much for the brave DIY enthusiast, but we’re always here to offer some friendly advice. Some exterior decorating projects can feel a little overwhelming for the novice though, so if you live in Toronto or surrounding areas, please feel free to contact The Toronto Painters for a quote!

Source: https://thetorontopainters.ca/

Paint Steps

Don’t want to paint yourself into a corner? How about getting stuck up or down the steps after you paint them. Well I have a solution so you don’t get trapped!

1. For outdoor or basement steps mix a little bit of sand with your paint and you’ll have a gritty surface to step on and less chance of slipping.

2. When it comes to painting the steps there are a couple of ways you can do it. To ensure that you can use the steps while they’re drying, paint half of the step so that you can walk up or down on the other side. However, I prefer to have a nice smooth look on each step without a line in the center, so I like to paint every other step. This way you can skip steps while you’re going up and down. Let those dry and then go back and paint the other steps!


Painting tips & tricks

Rub petroleum jelly on the hinges and door knobs before you start to paint a door. If you get paint on them, they will wipe off easily.

To keep white paint from yellowing, add 2 drops of black paint to each Gallon of white.

When painting ceilings, cut a child’s rubber ball in half and put your paint brush in one of the halves to catch the drips.

An old pair of swimming goggles will protect your eyes from paint splatters and drips when painting ceilings.

When painting, protect your hands and face with moisturizer. Cleanup will be easier and the moisturizer will prevent paint from seeping into the pores.

To stop paint from dripping, punch a few holes in the rim of the paint can. When the brush is wiped against the edge, the paint flows back into the can. The lid covers the holes so the paint won’t dry out.

Before pouring paint from a can, cover the rim with masking tape. After pouring, remove the tape — the rim will be clean and the cover will fit tightly.

To remove lumps from paint: Cut a piece of screen to fit the inside of the paint can. Set it on top of the paint and let it float down to the bottom of the can. It will take all the lumps with it, trapping them at the bottom of the can.

When painting a room, dip a small card into the paint so that you have the exact colour with you and can match accessories in store.

When painting inside corners, trim the paint brush bristles to a V to save strokes and spread paint more easily.

When you poke a paint brush into corners or allow it to rest on the bottom of the paint can, the bristles curl and stray. To straighten natural bristles (not synthetics), try wrapping the brush in a couple of thicknesses of damp cloth and press gently with an iron. The steam and cloth binding do the job. Only light pressure is needed. Let the bristles cool before you unwrap the brush.

When painting old woodwork fill in the holes or cracks with a mixture of flour and some of the paint you are using. It hardens like cement and matches perfectly.

How to Paint the Exterior of a House

This may be the most important painting (and preparation) you do. Paint and preparation vary with the type of surface: wood, stucco, metal, masonry. Check with your paint store.

1. Repair or replace any damaged surfaces, whether wood, stucco, masonry or metal.

2. Wash off all surfaces. Use a high-pressure water sprayer (available to rent) to reduce labor. Make sure that surfaces dry thoroughly.

3. Use sandpaper or a paint scraper to remove any loose, cracked, chipping or blistered paint — down to raw surfaces if necessary. Use a small drop cloth as you go to catch loose bits of paint and debris. If you decide the exterior needs to be sandblasted, hire a licensed professional.

4. Patch all nail or screw holes, gouges and cracks.

5. Caulk such places as seams and corners, above door and window trim, and where trim meets siding – or where any material meets a different kind of material, such as trim over masonry. (Exception: Don’t use caulk where siding or shingles overlap or between shingles.) Use high-grade exterior caulk. Better caulks (such as silicone) actually bond to surfaces like glue and resist breaking down.

6. Use epoxy filler (the material used for car bodies) to repair serious problems in woodwork.

7. Cover dark stains – a wood knot, old paint, wood stain – with a stain-blocking primer. The same goes for mildewed areas; you can find primers and additives made especially for mildew.

8. Sand all rough or glossy surfaces; paint needs a slightly roughened surface to stick to. You can also use paint deglosser on all glossy surfaces. Remove sanding dust and debris.

9. Remove or cover all light fixtures, plumbing outlets, electrical covers and house numbers.

10. Remove all screens. You don’t want to get paint on them; it’s difficult (or impossible) to remove.

11. Use drop cloths to cover everything you don’t want to paint, such as plants, walkways, cars and your neighbors’ property.

12. Apply primer over all raw surfaces. Note that different surfaces – paint, metal, wood, stucco – require different primers.

13. Allow the primer to dry, then apply at least two coats of exterior paint. Let each coat dry between applications according to the manufacturer’s instructions. Use a brush on all woodwork and a paint roller or spray machine for everything else.

Exterior Repainting – How to Paint Exterior Masonry Walls

Painting your exterior masonry walls is a decision that should be made for the purpose of aesthetic reasons and equally to consider the need for a moisture sealing agent. While wanting things to be pleasing to the eye, preservation of your masonry surfaces must be taken into consideration when choosing an application or finish. Once a choice has been made regarding what look you wish to achieve for your exterior masonry walls, you may purchase your painting products to complete the job.

What You Should Know Before Painting Masonry Work

Before you apply any products to a newly built masonry wall, you must allow six to eight weeks for the purpose of curing any mortar or concrete. Curing is the process of drying and hardening of masonry structures to obtain optimal weight distribution. Hardening of concrete type masonry work is part of the process to create a strong and well balanced structure. Adding rebar to the center of concrete structures gives it even more sustainability. Any attempt to apply products prematurely to masonry surfaces before it has cured out completely, will lock in any unreleased moisture. Making this mistake can be a costly one because it is very likely structural damage and breakdown will occur. Another threat when sealing moisture into a surface, is the possibility of black mold becoming trapped inside masonry work This will cause a continual growth of this mold in and around mortar lines, This problem is very difficult to remedy.

Product Information and Overview

If your masonry work contain porous surfaces, you may wish to reduce its textured surface.. To create a smoother surface, using block filler. Block filler is a high performance product containing vinyl, acrylic, and, latex. It is, by far, the best solution for filling in small cracks and porous surfaces. This products intended use began some years back primarily used as a filler for cinder block. This is the reasoning for its name. Since then, block filler has broadened its horizons to include most masonry surfaces such as concrete and brick. The consistency and appearance of block filler is comparative to Elmers glue. Do not worry about difficulty in applying this product because it can be diluted with water at a ratio of ½ pt. for each gal..of block filler.

Application of Block Filler

Block filler can be applied using many different methods. Spraying block filler with an airless paint sprayer is only one method of applying it. It must be diluted following the ratio of ½ pt. to 1 gal. of block filler. This product may also be applied with a paint roller using a heavy nap roller sleeve. (1 in. to 1 ½ in. thickness) The term sleeve refers to the woolly tube that is slid over the roller frame, used to apply block filler or paint to a wall. The other way you may apply block filler to a surface is by using a paintbrush. If you find it difficult to spread and cut in, diluting it at the same ratio as above will make for an easier application. No matter which application method you choose to use, after completion you must give it a dry time of at least overnight. Once your block filler has dried completely, you may begin painting your exterior masonry walls.

Painting exterior masonry walls can be a tedious job to do. With some knowledge of products to use and tips on how to apply them should greatly decrease your stress level if you must tackle painting them.

Paint Products for Masonry Walls.

Paint products used, following the application of block filler includes latex and acrylics. Even solvent based paint products may be applied to block fillers. To further increase performance of block fillers different types of epoxies may be added directly into the block filler. Times that the need for hardening agents, such as epoxy is needed, is when the masonry structure to be sealed is exposed to continual and copious amounts of moisture.

Application Methods of Paint to Masonry Walls

Using an airless paint sprayer is an acceptable method of applying paint to masonry walls. If block filler has been applied prior to spraying the walls, just simply applying two good coats of paint will provide sufficient coverage. If a block filler has not been applied to the masonry walls then, throughout spraying the paint onto the surface, it must be brushed in, not to wait until the paint has dried. You must brush it into the surface while the paint is at its wettest so it will seep as deeply as possible into the pores of the masonry work. Coverage of paint to masonry surfaces not containing block filler is a much slower process of application. Many times it require several coats of paint to adequately cover its surface. Using a paint roller to apply paint to raw masonry surfaces usually has greater success in coverage using fewer coats to do it in. As indicated above, brushing paint on a masonry wall has a level of difficulty when trying to cut in because you need to load your paintbrush extremely full of paint in order for it to seep into its pores. This can be a messy venture. Nevertheless, it is still a way of applying paint to your exterior masonry walls.

Clean Up

Cleaning up block filler is done best with warm soapy water, but just water alone will work. You can use water to clean up latex and acrylic paint also. To clean up alkyd paint products (also known as oil based products) solvent clean up is necessary. Using mineral spirits or lacquer thinner is necessary for the clean up of any alkyd or oil based product.

Painting exterior masonry walls is much easier if a block filler has been applied prior to painting. Although it is not necessary, but it is advisable. Aside from making the surface easier to paint still is not the most important factor of using block filler. The main purpose of using block filler is to create a moisture barrier for your masonry structures. When painting masonry surfaces, applying block filler is a very important step and should always be included in the process.

Exterior Painting Pointers – What to Consider When Choosing House Paint Color

Choosing one’s house paint color appears to be an easy and exciting thing to do. However, when the actual purchasing is already on hand, homeowners become stumped and suddenly find it hard to come up with the ultimate decision.

Definitely, the paint color of a house speaks of the owner’s personality. The house paint color often stays for years, thus it is important to make the right pick so that living inside it would prove to be worth the investment.

Here are some suggestions that might help you in arriving at your envisioned house paint color.

Budget Planning

Before leaping into the house paint shopping frenzy, talk to an experienced person and ask for a list of things to purchase. Canvass the prices of these items so that you can compute how much you need to allocate for the painting materials.

Negotiate with Suppliers

There are suppliers who provide payment schemes or offer discounts for bulk purchasing. Some also provide house paint color advice depending on the owner’s needs. Do not hesitate to approach the suppliers; they would be more than happy to serve you.

Color Psychology

Psychologists say that colors generate emotional responses and depict one’s personality make-up. Gray means neutrality, blue speaks of calmness and green is reflective of the need for high self-esteem. Red goes for the vital and active person, yellow connotes happiness and cheerfulness, and violet conveys the wish to charm others. Brown, on the other hand, symbolizes roots and family security, while black expresses nothingness but highlights the attributes of the color around it.

Color Mixes and Matches

The personality color enhances the inner strength and rejuvenates a person. Make sure that you combine your favorite colors with shades that you intuitively know will bring you comfort and maintain your balance. Suppliers and other resource persons can provide you with the appropriate mixes and matches and can even create the tints of your fancy other than the ready-made swatches.

Choose Environment-friendly Products

Check also for environment-friendly paint products so that you do your share of preserving our Mother Nature. There are paint products that are odorless which minimizes health risks.

Consult other House Members

Decision-making should be done with the consensus of the majority. This may be a hassle for some but listening to the general opinion of your family members makes the choosing of house paint color much more fun. If you are living alone, consult friends’ counsels but in the end, the buck still stops with you.

Talk to a Professional

If you are loaded and can easily afford a house decorator or interior designer, explore current trends and house paint color themes that coordinate with the architectural design of the house. Better yet, explain to the professional the look that you want and they can work out the details conveniently for you.

When everything has been prepared and organized, go ahead and make the deal. Bear in mind that your house paint color reinforces your style and becomes the beautiful wrapper that covers the real surprise gift inside.

Exterior Painting Pointers – Tips for Painting with Crusher Dust

Whenever you are painting with marble dust, you will need to master a few techniques to get the best results. This type of painting is a great way for you to be able to get interesting and unique textures that you would normally not be able to achieve. Painting using this method is something that will require a little bit of getting used to but you will find that it is something that is a lot of fun to practice.

Preparation

You will need to prepare the mixture before you can begin. This is something that can take a couple of hours. You will need to begin by mixing the dry rabbit skin glue along with water and putting it into your crock pot. You will need to let this solution have time to soak for a couple of hours. Do not turn your crock pot on but do put the lid on. Once it has set for a couple of hours, turn on the crock pot. You will need to do this just to let the glue melt. You do not want this mixture to boil. Take care to stir it completely as it melts.

Safety

Once you have allowed the glue to melt you are going to be working with a few things that are a little bit more dangerous. Make sure that you put on either a dust mask or a respirator. You will mix a cup of titanium white pigment with a cup of marble dust in another container. Make sure that they are mixed together thoroughly before you combine it with the glue that you just melted. Make sure that you use caution as this glue is going to be very hot. Stir as you do this so it cannot get clumped together. This is something that you are going to have to do slowly and carefully. Whenever you are putting the marble dust onto the palette, make sure that you use a palette knife and that you are wearing your respirator. Go slowly and use caution as this dust will easily get everywhere.

Mixing

Whenever you are mixing the oil painting medium, use something like linseed oil along with your marble dust. You will need to keep adding the medium until the dust is at a consistency that you prefer. This is something that is up to you as far as the consistency. If you want to have a thicker paste, you should add less oil painting medium, this is something that works well for an impasto technique. If you want the dust to be more opaque, then use more medium and less dust.

Types of Paint

You may want to use different types of paint besides oil. The process will be the same with any type of paint that you use. Once you have the medium used and have the consistency that you desire, you will need to get the paint color that you wish to use mixed in with your medium and dust mixture.