Painting Pointers I have some painting pointers to help you out!

Sure you know the basics of painting, but sometimes it’s the little hints that can make the job go more smoothly. I have some painting pointers to help you out!

1. Before you tape off your borders, rub the stub of an old candle around the edges on both sides of your roll of tape. This will help keep paint from sticking to the tape and pulling off of the wall when you remove it!

2. If your room calls for more than a gallon of paint, mix the two cans together. Even though the paint was mixed using the same formula it can have variations from can to can and you don’t want that showing up on your walls!

3. When cutting in keep a wet edge to prevent a hatband you know that line of paint that looks different than the walls where you cut in. To do this, work in small areas at a time and then roll the walls blending the paint as you go. Or work with a buddy, one of you can cut in while the other rolls the walls.

4. To remove your roller from its handle for cleaning, slip a plastic grocery bag over it, and pull the two apart. Simply drop the roller in your cleaning solution and toss the bag.

5. To clean the paint out of a paint pad, run it over a wire mesh screen under warm soapy water!


Painting tips & tricks

Rub petroleum jelly on the hinges and door knobs before you start to paint a door. If you get paint on them, they will wipe off easily.

To keep white paint from yellowing, add 2 drops of black paint to each Gallon of white.

When painting ceilings, cut a child’s rubber ball in half and put your paint brush in one of the halves to catch the drips.

An old pair of swimming goggles will protect your eyes from paint splatters and drips when painting ceilings.

When painting, protect your hands and face with moisturizer. Cleanup will be easier and the moisturizer will prevent paint from seeping into the pores.

To stop paint from dripping, punch a few holes in the rim of the paint can. When the brush is wiped against the edge, the paint flows back into the can. The lid covers the holes so the paint won’t dry out.

Before pouring paint from a can, cover the rim with masking tape. After pouring, remove the tape — the rim will be clean and the cover will fit tightly.

To remove lumps from paint: Cut a piece of screen to fit the inside of the paint can. Set it on top of the paint and let it float down to the bottom of the can. It will take all the lumps with it, trapping them at the bottom of the can.

When painting a room, dip a small card into the paint so that you have the exact colour with you and can match accessories in store.

When painting inside corners, trim the paint brush bristles to a V to save strokes and spread paint more easily.

When you poke a paint brush into corners or allow it to rest on the bottom of the paint can, the bristles curl and stray. To straighten natural bristles (not synthetics), try wrapping the brush in a couple of thicknesses of damp cloth and press gently with an iron. The steam and cloth binding do the job. Only light pressure is needed. Let the bristles cool before you unwrap the brush.

When painting old woodwork fill in the holes or cracks with a mixture of flour and some of the paint you are using. It hardens like cement and matches perfectly.

Interior Painting Ideas for your home

Are you looking for interior painting ideas? For all of those who are tired of the same old boring walls, consider various interior painting projects to spruce things up! There are so many ways that you can take a dull wall and make it nothing short of a masterpiece! We know that not everyone has the same levels of skills, but in the world in which we live, there are many avenues that you can take and tools that you can use to get the beautiful, colorful, and designed walls that you are looking for! Let’s not forget that we can paint a lot more than walls as well!

To start, we need to choose the surface to paint. If you are painting walls or other flat surfaces, you need to start with a good cleaning as well as repairing any damages that you may find. Patch any holes and repair any rips, tears, or seams. Then you can move on. For those who are painting other surfaces, you will need to do the same cleaning and repair, but you also may need to consider other steps as well. If the surface will not easily hold paint, you’ll need to use an etching process to help it along.

Okay, so how will you do your painting? There are many techniques to choose from. You don’t just have to paint the wall one color. You can use several in various patterns. This includes processes like ragging, rolling, and washing. In some techniques, paint is coated on to the wall then removed using sponges or rags. Or, if you want a more geometrical look, consider stripes as well as frames around the walls.

You also don’t have to limit your interior painting ideas to walls. You can paint furniture, masonry like fireplaces, as well as elements like molding, doors, and windows. There is no limit to the things that you can paint with the right materials at your side. Painting is a great way to show off a new look or tone within a home. It can enhance or be the focal point of the room. And, just a few coats of paint will end up leading you to a completely different looking room, within minutes.


Painting tips & tricks

Rub petroleum jelly on the hinges and door knobs before you start to paint a door. If you get paint on them, they will wipe off easily.

To keep white paint from yellowing, add 2 drops of black paint to each Gallon of white.

When painting ceilings, cut a child’s rubber ball in half and put your paint brush in one of the halves to catch the drips.

An old pair of swimming goggles will protect your eyes from paint splatters and drips when painting ceilings.

When painting, protect your hands and face with moisturizer. Cleanup will be easier and the moisturizer will prevent paint from seeping into the pores.

To stop paint from dripping, punch a few holes in the rim of the paint can. When the brush is wiped against the edge, the paint flows back into the can. The lid covers the holes so the paint won’t dry out.

Before pouring paint from a can, cover the rim with masking tape. After pouring, remove the tape — the rim will be clean and the cover will fit tightly.

To remove lumps from paint: Cut a piece of screen to fit the inside of the paint can. Set it on top of the paint and let it float down to the bottom of the can. It will take all the lumps with it, trapping them at the bottom of the can.

When painting a room, dip a small card into the paint so that you have the exact colour with you and can match accessories in store.

When painting inside corners, trim the paint brush bristles to a V to save strokes and spread paint more easily.

When you poke a paint brush into corners or allow it to rest on the bottom of the paint can, the bristles curl and stray. To straighten natural bristles (not synthetics), try wrapping the brush in a couple of thicknesses of damp cloth and press gently with an iron. The steam and cloth binding do the job. Only light pressure is needed. Let the bristles cool before you unwrap the brush.

When painting old woodwork fill in the holes or cracks with a mixture of flour and some of the paint you are using. It hardens like cement and matches perfectly.

Prep & Exterior Painting


1. Wash you’re siding with an inexpensive hose- mounted brush, such as a car-washing brush. Work from the top of the wall to the bottom. Use household detergent on tough spots and rinse all soapy areas thoroughly.


2. Scrape away peeling paint with a paint scraper. Don’t gouge the wood, and be sure to change (or sharpen) the scraper blade frequently to make the work go faster.


3. Use 100-grit sandpaper over a sanding block to smooth the scraped areas. Feather the edges so they match the surrounding surface.


4. Use a flap sander mounted in an electric l (or a cordless drill for very quick jobs) to remove peeling paint from curved surfaces. This tool works on both concave and convex boards.


5. On larger scraped areas, use an electric sander to smooth the surface. U e 100-grit sandpaper and be sure to brush the sanding dust off he siding or trim when you’re done.


6. Fill any cracks between the siding and the door and window trim using a caulk gun and paintable, exterior caulk. Fill deep cracks in a couple of passes to keep the caulk from smearing on the siding.


7. Prime and then paint all sanded areas. And, try not to over-brush. Because paint tends to fade over time, your touch-ups will look brighter than the original paint covering. Keeping their size as small as possible will make them less noticeable.


8. Try to remove any paint splatters from window glass before they dry. Once the paint hardens ifs much harder to remove.

Interior Painting Ideas

Guaranteed to Bring Your Walls Back to Life!

There are many different interior paint ideas you’ll discover that can be used to add style, and change the look of your rooms. As you begin decorating the rooms of your home.

Interior paint ideas are about being creative and you can be as creative as you wish. Plus, you shouldn’t have a problem when it comes to controlling your budget.

That’s because most of the materials you will need can be acquired for a small amount of money. However, you should remember that although interior paint ideas do not have to be expensive, creating your designs with them, can take quite a bit of your time.

So, be patient, because hurrying your paint designs will often result in an unrewarding outcome.

The following are some of the different ways you can use interior paint ideas to dress up the look of your walls:

Rag Rolling – Rag rolling is done by rolling up a rag as you would a magazine or newspaper, and then rolling it with your hands over the wet paint that has already been applied to the wall.

Stencilling – Stenciling is one of the best interior paint ideas because it is one of the easiest and cheapest ways to decorate your walls. Stenciling works by painting the areas that have been cut out of a template.

Then once the template is removed, a defined pattern or design remains. You can create your own stencils, if you have the proper materials, or you can purchase them at craft or specialty stores. Stencils come in various sizes and designs, and you can place them on any part of your wall to either create a picture, or boarder.

You should remember, however, that it is a good idea to use a darker or light color for your stenciling patterns to contrast with the main color of the wall.

Bagging – After the wall has been painted you can then use the bagging interior paint ideas to create interesting wall patterns, by placing a cloth that has been bunched up into a bag, and then dragging it over the wall.

Sponge Painting – For sponging interior paint ideas all you require is a simple sea sponge, and a tray to hold the glaze paint of your choice. You can then proceed to sponge the wall as intricately or loosely as you would like to create the desired effect you want. You will find that with sponging, you can create a lovely marble look on the wall.

Other interesting interior paint ideas you can create if you are more adventurous include dragging, stippling, combing, granite finish and marbleizing.

Types of paint that you should look into for your painting project include:

• Latex

• Latex flat enamel

• Alkyd

• Enamel

• Epoxy

As you can see there are several great interior paint ideas for you to check out and use to create some of the most wonderfull designs on your room walls. Take your time decorating your rooms, and you will love the result of your work.

Interior painting problems

Covering Stains, Grease, Graffiti, and Problem Surfaces.

Most folks find out about stains and problem surfaces after it is too late — during, or after they are done, painting. Repeated coats of paint won’t cover properly because the problem areas bleed through the new paint.

Special Problem Areas

• Old paint, oil or lead based
• Grease, oil, mold, or mildew
• Graffiti, ball point ink, permanent markers, paint
• Bad plaster, crumbling or water damaged

Old oil and lead base paints often used special pigments that bleed through new latex paints. Light colors might not bleed at all while some darker colors cannot be covered even with several coats of paint. You can test a small area, let it dry for 24 hours, and check for coverage.

To seal the old paint, you need to use a special primer. Normally, it will be an oil base primer especially made to cover oil base paint before painting with latex paint. Be sure to get one designed for this purpose. Be sure to follow the directions for drying time before applying the first coat of paint.
Grease, oil, mold, or mildew should be cleaned with a household clearner first. Next, clean with a solution made for use before painting, such as Soilax. You can purchase it at a paint or hardware store. After the soiled areas are dry, paint them will a special primer designed for hiding these kind of spots.

Porters–Stay-Kill–primer works well. You can prime the entire surface, or just cover up the soiled areas. Be sure to follow the directions for drying time before applying the first coat of paint.
Graffiti, ball point ink, permanent markers, and paint can be covered with a special primer designed for hiding these kinds of spots. Porters Stay-Kill primer works well. You need to cover the soiled areas. Be sure to follow the directions for drying time before applying a second coat of primer or the first coat of paint.
Bad plaster, crumbling or water damaged needs to be cleaned first. Use a scrub brush and water to remove all the loose plaster. If there’s extensive damage, you should repair the damaged plaster, too. Water damage causes some of the chemicals in plaster to bleed through new paint. It’s a good idea to use a primer like Porters Stay-Kill before painting. Be sure to follow the directions for drying time before applying a second coat of primer or the first coat of paint.

Painting tips . . .
Buy good quality paint. Porters are one of the brands that are good, however, other name brands are good, too, and have similar types of primers and paints.
In kitchens, bathrooms, and high-traffic areas, use a “latex enamel” paint which is more waterproof and can be cleaned easily
Allow plenty of drying time for a primer, and between each coat of paint. Getting in a hurry might end up with a poor finish, or require an additional coat of paint
If you’re trying to get by with just one coat of paint, don’t apply it to heavy. If a second coat is needed, you will have wasted paint
If you plan to use two coats of paint, don’t put the first coat on too thin. Two even coats will look better and last longer
Be sure you have plenty of ventilation. If you’re painting your home, plan to does it during warm weather so you can leave the windows open during, and for several days after, painting?

Interior Painting tips

Painting walls is a chore, and one that you will want to get right the first time around. Failure to paint the wall properly will cause the colors bleeding; running and you will have to add many coats of paint to cover these mistakes.

Place drop cloths on the area around where you are painting. Some paints say they wash up with soap and water, and the paint still is hard to remove.

Purchase paintbrushes for oil paints or latex, depending on which paint you are using. Same thing goes for the paint roller. It should have a medium nap. If preferred, you can use a paint sprayer and can purchase one at your local hardware center or home improvement center.

You can paint oil based paints over latex, but you can’t paint latex based paints over oil based paints without first prepping the walls. You can buy an etching solution or use a primer to seal in the oil paint. After you have primed the wall, you can begin painting.

First you will want to start with your ceilings. Feel free to paint over the edges because when you paint the walls, you’ll cut your corner in.
Next is your woodwork. Sand and prime before you paint.
Use a semi-gloss enamel paint on your trim and a flat finish or eggshell paint on your walls. Trim being doors, molding etc.

Now that you have finished the ceiling, you can paint the walls. Cut in first with a paintbrush. You do this by painting the corners and areas that the paint roller will not reach.

Roll out two coats on your walls, being sure you let the first coat dry thoroughly first. Be sure to have a window or fan for proper ventilation. If it’s cold outside, make sure the heat is on in your home to help dry the paint.

Be sure to use quality paint. If you have children, you will want to make sure the paint can be washed. Also make sure the paint has a warranty for at least 5 years or longer.

After painting, be sure to clean the brushes, roller and roller pans for your next project.


Interior Painting – Frequently asked questions

Can I paint directly over wallpaper?
No. Wallpaper can be painted over with the proper preparations. Be sure to remove any loose wallpaper, scuff/sand the surface, then apply interior oil-based primer.

Can I apply latex paint over oil based paint?
Yes. Be sure to prepare the surface properly before painting. Oil-based paints should be sanded to a flat finish before painting. After rinsing, apply Dutch Boy® oil-based primer and apply desired latex paint.

Can I apply paint directly over a semi-gloss paint?
No. Semi-gloss paint must be dulled to a flat finish by sanding*, allowing proper adhesion. Removing or disturbing old paint from interior or exterior surfaces by sanding, scraping, abrading or other means may produce dust, debris or fumes that contain lead. Exposure to lead dust, debris or fumes may cause brain damage or other adverse health effects, especially in children and pregnant women. Structures built before 1978 should be tested by a licensed inspector prior to removing or disturbing old paint.

Can I use exterior paint on the inside of my house?
No. Exterior paints are formulated to be more flexible to withstand temperature and climate change.

How can I best prepare my walls before I paint?
Walls that have never been painted should have a recommended primer applied before painting. For previously painted walls, thoroughly wash them with a mild soap and water solution, then rinse with clean water. If your existing surface was painted previously with semi-gloss paint, the surface should be lightly sanded to a duller finish. If the walls have not been painted in five years or longer or are stained then primer should be used.

How much paint do I need?
To achieve one-coat coverage, paint should be applied at a maximum of 400 square feet per gallon. Rough or textured surfaces may require more paint. On these areas allow for 125-300 square feet per gallon.

How do I prepare the surface?
As a general rule, all surfaces should be clean before painting. Remove any loose, peeling paint, and/or any other substrate that is on the surface*. Scrub all surfaces to remove all dirt, grease, oil, etc. Rinse surface well and allow to dry. Apply appropriate patching material to cracks, nail holes, or other surface imperfections, sand smooth, and remove sanding dust.

*If your existing surface is glossy, dull surface by sanding or use an abrasive cleaner. Remove any residue.

How do I take care of my freshly painted surface?
Freshly painted surfaces may be washed after 30 days. Avoid touching, wiping, or wetting any freshly painted surface for 30 days. After that time dirt and stains may be removed with a mild, non-abrasive cleaner and water. Do not place objects on windowsills and shelves until paint is thoroughly dry.

How long should I wait before applying a second coat of paint?
A second coat of latex paint may be applied 6 hours after the first coat. With oil-based paint, you should wait 24 hours between coats.

Should I paint the trim before or after I roll the walls?
The wall area around the doors and windows and along the ceiling should be cut in with a brush, this will prevent the wall from having an obvious and unsightly picture frame effect. Then, the main part of the wall can be painted with a roller, rolling into these areas.

Why do I need to use a primer?
Primers are specifically formulated to seal porous surfaces, block stains, as well as to insure the proper adhesion of the topcoat and produce the best possible coverage.

What is the proper order to follow when painting a room?
When painting a room, the ceiling should be painted first, followed by the walls, then the trim (including doors and windows) and finally the baseboards.

When should I apply?
Room and surface temperature should be between 50 and 85 degrees. Paint dries best between 65F and 85F. Allow at least 4 hours of drying time before recoating.

What is the proper rolling technique?
Fully load the roller with paint by dipping the entire cover deep into the tray of paint. Carry as much paint to the surface as possible. Make a letter “V” in a small 2 foot by 2 foot area with a generous roller load of paint. Fill in the “V”, spreading the paint evenly from left to right. Lightly smooth out with downward motions. Repeat “V” with a freshly loaded roller for every 2 x 2 foot area.

Interior Painting Ideas

Kitchens:
The kitchen is a room you will tend to spend a lot of time in, especially if you are the main chef in your household. Make sure you are comfortable with your chosen colour scheme as you will probably spend a significant amount of time surrounded by it. Bright, invigorating colour schemes can boost energy levels when you have a lot of cooking and cleaning to get through.
As kitchen walls tend to be dominated by cabinetry, benches and the floor, treat these elements as the starting point for your colour scheme.

The appearance of colours in the kitchen will depend on the properties and textures of each of the surfaces. Glossy surfaces, such as Melteca cabinetry, will reflect more light and look different to low sheen painted walls, so it is important to be careful when trying to match colours in different materials. Sometimes it is better to select a tone lighter or darker rather than trying to create an exact colour match.

Remember no matter what room you are decorating, artificial lighting can be used very successfully to compliment your colour scheme and it is worth reviewing your lighting plan prior to painting.

Living Rooms:
Today’s living rooms are often open spaces that link through to dining and kitchen areas. Knowing where to start and finish the colour scheme between each part of an open plan space can be very difficult. There are two techniques that you can use:
Paint a feature wall in an area between the two adjoining rooms/spaces to create a natural colour break.
Use a progression of colours, then paint a unifying colour throughout the spaces and accent with the other progressional colours.

Living rooms are the ideal place to create focal points or feature walls. Traditionally fireplaces acted as the focal point of most living rooms. If you don’t have a fireplace, select a focal point for your room and decorate around that. The focal point may be a feature wall, lounge suite or similar.

As living rooms are usually subjected to less wear and tear than family rooms, you can choose light and dark colours if desired.

Bedrooms:
When selecting colours for bedrooms it is important to choose colours that are conducive to sleeping. You are also likely to spend more time looking at the ceiling than you would in other rooms.

As a general rule you should avoid using very bright colours and save them for other parts of your home. Most light and pastel shades are ideal for bedrooms. Blue is a popular colour choice for bedrooms because of its soothing qualities. However, if you have trouble getting up in the morning, you may wish to add an invigorating accent to get you out of bed.

Bathrooms:
Bathrooms are one of the smallest rooms in the house and are generally cluttered with towel rails, basins and showers/baths. While this can make them a decorator’s nightmare, it also means you can afford to be a little more courageous with colour. If your original colour choice doesn’t work, you can always repaint a small bathroom quickly.

Avoid using too many colours if your bathroom feels small. Instead, paint a dado on the bottom third of each wall in your chosen colour and paint the remaining two-thirds in white.
Blues and greens are popular choices for bathrooms as they are tranquil and clean. Being cool colours, they can also make your small bathroom appear more spacious.

Painting Home Basics

Interior Painting

When painting a room, it¹s best to paint the ceiling first, followed by the walls, with the trim, cabinets, and doors painted last. Work from the top down. In order to keep a wet edge, only cut in one wall at a time before you begin painting with rollers.

Brushes are used to cut in around the ceiling, trim, windows, and doors before using a roller. They are also used to paint the trim, window frames and doors. There are a number of brush sizes available in both straight edge and angled sash. Your choice depends upon the size of the area you are painting and whether you prefer a straight edge or an angled sash. Rollers are a great time saver for painting larger flat surfaces such as ceilings and walls. Roller covers come in various nap lengths. Your choice depends upon whether the surface to be painted is smooth or if it is more textured. The more textured the surface, the longer the nap should be in order to allow the fibers to push the paint into the crevices on the surface.

High quality applicators will provide the best painting results. Cheap or low quality applicators can make the best quality paint look and perform poorly. Cheap roller covers do not spread the paint evenly on the surface, and often leave fuzz from the roller on the wall. Inexpensive brushes are harder to use because they do not spread the paint evenly and leave unsightly brush marks. High quality applicators can be cleaned and used again.

When painting, always work from the dry area into the adjoining wet paint area. Use the “N” technique when using a roller. Load the roller completely. Apply the paint in the form of an “N” in a 2¹ x 2¹ area. Fill in the center of the “N” with horizontal strokes from side to side. Lightly smooth the painted area with vertical strokes from top to bottom. Continue to use the “N” pattern with a freshly loaded roller directly below the first “N”, working until you reach the bottom of the wall.

Timesaving Tip: If you take a short break from painting, you can wrap your applicators tightly in a plastic bag or aluminum foil instead of washing them!

Always be sure to stir the paint thoroughly before using and do not thin the paint. If you are using more than one gallon of the same color, mix them together in order to insure color consistency. Paint when the room and surface temperature is 50ƒF or above. Avoid touching, wiping, or wetting a freshly painted surface for 30 days to allow the paint to completely cure. After 30 days, the painted surface can be cleaned with a mild, non-abrasive cleaner and water. Do not place or hang objects on the surface until the paint is thoroughly dry.

Remember: Its important to follow the directions on the back of the paint label. It contains the most important information you need for your painting project.

Painting Concrete Floors

Preparation is especially important when the surface to be painted is a concrete floor, such as in a laundry room or workshop. First you will want to repair any cracks or holes. You will next need to prepare the concrete with a muriatic acid solution. This process is called “etching.” It’s similar to etching glass— scraping off a bit of the top so that the paint has something to adhere to. Caution: muriatic acid is strong enough to burn skin and eyes. Before you begin the etching process, put on the proper safety gear. If you can’t ventilate the work area, wear a dual-cartridge respirator.

How to prepare and paint a concrete floor:

1. First, sweep and scrape off the dirt from the floor. Clean off any grease, oil, and other contaminants using a cleaning solution.

2. Rinse the floor well to remove all traces of the cleaning solution.

3. Mix the solution to etch the floor by adding 1 part muriatic acid to 3 parts water. Do it in this order—do NOT add the water to the acid.

4. Apply the solution, using 1 gallon per 100 square feet, and scrub the floor with a stiff-bristled brush. Leave the solution on the floor until it stops bubbling.

5. Rinse the floor thoroughly with clean water. Wipe it down with a damp sponge mop to eliminate puddles.

6. If the floor isn’t dry in four hours, repeat the rinsing procedure.

7. After the floor is completely dry vacuum it to remove any powder residue left by the muriatic acid solution.

8. You can now paint the floor with an alkyd or urethane latex floor and deck enamel. It is best to paint with a roller and long pole. First paint the edges then work from the wall farthest from the door back toward the door.

Home Painting Tips

Painting Tips & Ideas

Your home is the best place to spend your quiet moments together with your family. You can do whatever you like and you get to choose your home’s color every time you need to paint it.

Many families prefer to change their home’s paint when the season changes and they feel that a new coat of paint is already necessary. Summer comes after the winter, so you might want to have your home’s atmosphere changed to accommodate the summer feel. This is easily done by painting your home. Just make sure that you paint it with colors that depict the summer time.

Check out these cool tips so that you can decorate and paint your home for the summer:

1. When you talk about summer, you instantly think of lively colors. Everything seems so bright when summer comes and so there is a need to change your home’s paint into bright colors. By using bright colored paints, your home will open up and it’s like bringing the outside world inside.

2. Have you heard about decorative painting? This is a technique used in painting which is divided into sponging, stenciling/stamping, and ragging. By using these different techniques, it would be a lot easier to brighten the dull house paint that you now have.

3. Before starting the actual painting, you should pick the right color scheme for your home. Remember that the techniques mentioned above require the use of two shades so this is very important step that you have to never forget.

4. If you prefer to sponge your wall, or rag it perhaps, paint first the base color. Leave it to dry thoroughly. Afterwards, dip the rag or sponge to the lighter color paint that you’ve chosen. Drag or sponge the light colored paint over your base coat; do this until you’re satisfied with the effect.

5. If after your painting home summer-project you’re not that satisfied with some of the results, repaint those areas using your base coat.

6. Some people like to do stamping or stenciling when they paint their homes. This technique creates a design that looks like wallpaper over the base coat. Choose a design that has something to do with the summer. It takes just a few artistic touches and creativity to create something that depicts summer season.

7. Choose the paint for your home carefully, as well as the tools needed. Prepare the walls where you need to change the paint. This way, you can expect a much better result.

8. Visit your local paint shops or hardware for the paints that you’ll need. You can even consult the people there and ask for pieces of advice regarding painting your home with a summer theme. The people there will be most willing to test small amounts of paint for your desired color scheme.

9. If you have excess paints, make sure that you keep them in metal cans that are airtight and sealed. The shelf life of paints is reduced once the can is opened, so you can only keep it for a short time for later use.

Now, there are a lot of paint colors that you can choose for your home painting project. The paint greatly varies from texture, color, to patterns. The color of paint that you choose can affect your home’s structures and other things inside your home. So make sure that you choose the right color for the different rooms of you house. The colors should blend together to create the perfect summer atmosphere for your home.